Home -> Maritime -> Marine Maintenance Repair Electronics Lighting

PREVENT PREMATURE MAINTENANCE & REPAIR CAUSED BY RUST, CORROSION AND ELECTROLYSIS WITH SHIP 2 SHORE ANTI CORROSION, DIELECTRIC WET FILMS

PROTECT MARINE ELECTRONICS & LIGHTING AGAINST RUST AND CORROSION

Ship-2-Shore protection from rust for marine maintenance, anti-corrosion for electroncis & lighting for boats, sailboats, yachts, workboats, tugboats, coast guards boats, barges

High performance anti corrosion rust remover for marine maintenance repair. Remove rust, stop corrosion and electrolysis on marine electronics, control panels, electrical wiring and motors. Ideal wet film anti corrosion protection for workboats, barges, ships and other vessels. Vessel bilge and cargo hold, drive shaft tunnel and engine compartment, lazarette and rudder, deck equipment and cargo.

Use Ship-2-Shore films to stop rust in voids, joints, seams, cracks and corners. Effective on steel, stainless steel, aluminum, galvanized, copper, etc.

Temperature related expansion and contraction of metal eventually results in cracking, separation and peeling of typical hard coatings used as corrosion protection. Paints, sealants, plastics and other coatings expand and contract at different rates. Use Ship-2-Shore films over paint and other coatings to find, coat and protect base metal exposed by cracks, chips and peeling. Extremely resistant to salt water, salt spray and other contaminants, Ship-2-Shore films do not attract dust or dirt, nor become gummy. Ship-2-Shore films resist splash, spray and even complete submersion.

PROTECT ELECTRONICS AGAINST RUST

  • Rust is a never ending battle. Water gets into everything, even the most robust components and fixtures. Almost 50% of all electric, electronic and mechanical component failures are caused by corrosion.
  • Corrosion in electric, electronic and mechanical components is insidious and cannot be readily detected. When corrosion failure occur, it is often dismissed as just a failure and the part or component is replaced. The most common reason for corrosion-related failure is atmospheric humidity, condensation and environmental contaminants (dust, dirt, salt, etc.).
  • Extend service life. Improve operating efficiency. Reduce downtime, service & repair costs. Save on replacement part costs. Ship-2-Shore anti-corrosion films shut down electrolysis between dissimilar metals and stop rust and corrosion 100%
  • Corrosion inhibitor/ lubricant for Canadian mining and marine industries since 1960's. Industry Canada approved. Navy and Coast Guard proven.

"Ship-2-Shore is awesome! ...we use it on just about everything" Canadian Forces Member, Deck Crew, HMCS Winnipeg

SHIP 2 SHORE WET FILMS ARE MADE FOR INDUSTRY

  • 40,000v Dielectric, high performance long lasting protection from moisture and corrosive contaminants. No cracking, chipping or separation. Can be used on bare metal and to protect exposed metal where paint or other coatings and seals have cracked, chipped, separated or are not present. Can be applied over paint. Ship-2-Shore films are penetrant and migrate to base metal. Resist splash, spray and complete submersion. Ideal for exposed surfaces, insulated pipe and wire.
  • When applied, Ship-2-Shore films cure to form dynamic and non-hardening, dripless and self-healing coatings. Often referred to as wet film. Ship-2-Shore films adhere like a "magnet to steel" to prevent oxygen contacting base metal and shut down rust and corrosion 100%. Make excellent high pressure lubricant. Do not attract dust and dirt nor turn "gummy".
  • Corrosion proof and waterproof electronics, circuit boards, lighting, electrical, wire, connectors, switches, motors, machinery, tools and equipment, nuts, bolts, screws, fasteners, hinges, joints, seams, welds, cracks, voids, etc...
  • Shuts down electrolysis between dissimilar metals. Use Ship-2-Shore on steel, steel alloy, stainless steel, galvanized, aluminum, iron, copper.
  • Environment friendly. A little goes a long way and lasts. Ship-2-Shore films are classified non-hazardous, non-flammable and non-toxic. Approved for food processing, food service, food retail equipment and facilities.

SHIP 2 SHORE AVAILABLE IN TWO FORMULATIONS

Ship-2-Shore PLID Thin Film ( 40,000v dielectric ) - Makes an excellent thin, extreme penetrating, all purpose anti-corrosion, anti-seize and high pressure lubricant film. Ideal for electrical, electronics, circuit boards and mechanical. Float Coat PLID for difficult to access cofferdam voids, void between double hulls, tanks, rudder void, keel, etc.

Comes in:

  • 180 gram (6oz) aerosol spray (case of 12) *most popular product
  • 20 litre pail (5 gal)
  • 205 litre drum (55 gal)

Apply with aerosol spray, brush, mop, airless paint sprayer or floatation method. 1 litre covers up to 100 sq ft. Apply to bare metal, over paint or other hard coatings. Can be applied to damp surfaces.

Ship-2-Shore Industrial Thick Film ( 8920v dielectric ) - "thick" heavy duty, anti-corrosion, high pressure lubricant wet film coating. Ideal for long lasting corrosion protection under difficult, extreme conditions and just about anything else. Suitable for workboats, barges, ships, anchor chain, wire rope, offshore structures, deck equipment, electrical, vehicle corrosion preventive undercoat, etc.

Comes in:

  • 180 gram (6oz) aerosol spray (case of 12) *most popular product
  • 20 litre pail (5 gal)
  • 205 litre drum (55 gal)

Apply with brush, cloth, mop or airless paint sprayer. 1 litre (1 quart) covers up to 50 sq ft. Apply to bare metal, over paint or other hard coatings. Can be applied to damp surfaces.

"ULTIMATE IN MOISTURE AND CORROSION PROTECTION"

For further advice about the range of Thin Film, Industrial Thick Film, Thick Film, Float Coat or PLID Wrap, give us a call on (03) 9587 6022 or drop us a line!
EMAIL US